Hardware & Tools

2015 Ram 1500 Lug Nut Torque: Complete 1500 and 2500 Spec Chart

Getting the 2015 ram 1500 lug nut torque right isn’t just some number you pull out of thin air. It keeps your wheels clamped tight against the brake hub when you’re hauling a trailer or bouncing down a dirt road. Full-size pickups take a beating from rotational shear forces. Guessing at fastener tightness with an impact gun or a short tire iron? That’s how you end up with warped rotors or wheels that loosen at the worst possible moment. Here’s the official 2015 ram 1500 lug nut torque spec. You’ll also get every rating for Ram 1500 and heavy-duty Ram 2500 trucks, plus exact socket sizes, flange nut differences, and the star tightening sequences that actually matter.

Need a complete roadside walkthrough before you start lifting your truck? Check out our step-by-step guide on how to change a tire safely.

Key Takeaways

  • The official 2015 ram 1500 lug nut torque specification is 130 ft lbs (176 Nm) on clean, dry studs.
  • Every Ram 1500 built from 2012 through 2026 uses 130 ft lbs (176 Nm), including both 5-lug Classic and 6-lug fifth-generation models.
  • Heavy-duty Ram 2500 single rear wheel trucks require 130 ft lbs (176 Nm) for one-piece nuts or 165 ft lbs (224 Nm) for two-piece flange nuts.
  • Standard Ram 1500 and 2500 factory lug nuts require a 22 mm (7/8 inch) deep six-point socket.
  • Swollen two-piece Mopar chrome lug caps often require a 22.5 mm or 23 mm half-size extraction socket.
  • Always tighten Ram lug nuts in a crisscross star sequence while the truck weight rests firmly on level ground.

The “Before You Start” Checklist

Gather these essential tools before removing and tightening lug nuts on your Ram pickup truck.

  • Calibrated click-type or digital torque wrench: Rated up to at least 200 or 250 ft lbs (270 to 339 Nm).
  • 1/2 inch drive breaker bar: At least 24 inches (60 cm) long for breaking tight truck lug nuts loose smoothly.
  • 22 mm (7/8 inch) deep six-point socket: Thin-wall chromoly socket for standard factory Mopar lug nuts.
  • 22.5 mm half-size extraction socket: Crucial backup socket if your two-piece factory chrome caps have swollen.
  • 3 inch (7.5 cm) socket extension bar: Gives your torque wrench handle clearance outside deep truck fenders.
  • Wire bristle brush and clean microfiber cloth: Used to clean rust flakes and road grime off the brake rotor pad.
  • Heavy-duty wheel chocks and 3-ton (2,720 kg) jack stands: Essential for stabilizing full-size pickup weight safely.
  • Solid one-piece forged steel replacement lug nuts: Recommended if your original two-piece Mopar nuts show bulging.

2015 ram 1500 lug nut torque specification tightening with a calibrated torque wrench on an alloy wheel.

What Is the Official 2015 Ram 1500 Lug Nut Torque Specification?

The official 2015 ram 1500 lug nut torque specification is 130 pound feet (130 ft lbs). That converts to 176 Newton meters (176 Nm). This factory spec applies to all 2015 Ram 1500 trims, cab configurations, and both aluminum alloy and stamped steel wheels. Always torque clean, dry threads without oil or grease.

Interestingly, half-ton competitors use slightly higher clamping loads than Ram trucks. For example, our 2015 F150 lug nut torque guide details why Ford specifies 150 ft lbs (204 Nm) on its 14 mm studs. Ram engineers, however, calibrated the 1500 hub assembly for 130 ft lbs (176 Nm). Never apply 150 ft lbs to a Ram 1500 wheel. Over-tightening stretches the Mopar studs and warps the brake rotor hat.

Ram 1500 & 2500 Lug Nut Torque Chart by Year and Model (2012 to 2026)

Ram truck lug nut torque specs depend on the truck weight class, wheel stud diameter, and nut flange design. All 2012 to 2026 Ram 1500 models require 130 ft lbs (176 Nm). Ram 2500 models require 130 ft lbs (176 Nm) with solid one-piece nuts or 165 ft lbs (224 Nm) with two-piece swivel flange nuts.

Many drivers get confused because Ram sold the fourth-generation 5-lug Ram 1500 Classic alongside the newer fifth-generation 6-lug Ram 1500 from 2019 through 2024. Even though the bolt pattern changed from five lugs to six, the 2020 ram 1500 lug nut torque remained 130 ft lbs (176 Nm). Similarly, heavy-duty truck owners searching for 2016 ram 2500 lug nut torque, 2017 ram 2500 lug nut torque, or 2018 ram 2500 lug nut torque must check whether their nuts have a free-spinning flange washer. Review the complete reference chart below before setting your wrench.

Complete Ram 1500 & Ram 2500 Wheel Torque Reference Table

Model Year / Keyword Target Generation & Axle Type Lug Nut Torque (Imperial) Lug Nut Torque (Metric) Stud Thread Size Hex Socket Size Bolt Pattern
2002 to 2011 Ram 1500 3rd & Early 4th Gen (9/16 in) 135 ft lbs 183 Nm 9/16 in – 18 UNF 22 mm (7/8 in) 5 x 139.7 mm
2012 to 2014 Ram 1500 4th Gen DS Body (5-Lug) 130 ft lbs 176 Nm M14 x 1.5 22 mm (7/8 in) 5 x 139.7 mm
2015 ram 1500 lug nut torque 4th Gen DS Body (5-Lug) 130 ft lbs 176 Nm M14 x 1.5 22 mm (7/8 in) 5 x 139.7 mm
2016 to 2018 Ram 1500 4th Gen DS Body (5-Lug) 130 ft lbs 176 Nm M14 x 1.5 22 mm (7/8 in) 5 x 139.7 mm
2019 to 2024 Ram 1500 Classic 4th Gen DS Body (5-Lug) 130 ft lbs 176 Nm M14 x 1.5 22 mm (7/8 in) 5 x 139.7 mm
2020 ram 1500 lug nut torque 5th Gen DT Body (6-Lug) 130 ft lbs 176 Nm M14 x 1.5 22 mm (7/8 in) 6 x 139.7 mm
2021 to 2026 Ram 1500 (All & TRX) 5th Gen DT Body (6-Lug) 130 ft lbs 176 Nm M14 x 1.5 22 mm (7/8 in) 6 x 139.7 mm
2016 ram 2500 lug nut torque 4th Gen HD (Single Rear Wheel) 130 ft lbs (1-pc) / 165 ft lbs (Flange) 176 Nm / 224 Nm M14 x 1.5 22 mm (7/8 in) 8 x 165.1 mm
2017 ram 2500 lug nut torque 4th Gen HD (Single Rear Wheel) 130 ft lbs (1-pc) / 165 ft lbs (Flange) 176 Nm / 224 Nm M14 x 1.5 22 mm (7/8 in) 8 x 165.1 mm
2018 ram 2500 lug nut torque 4th Gen HD (Single Rear Wheel) 130 ft lbs (1-pc) / 165 ft lbs (Flange) 176 Nm / 224 Nm M14 x 1.5 22 mm (7/8 in) 8 x 165.1 mm
2019 to 2026 Ram 2500 (All Trims) 4th/5th Gen HD (Flange Nut) 165 ft lbs 224 Nm M14 x 1.5 22 mm (7/8 in) 8 x 165.1 mm

Why Does Ram Use 130 Ft Lbs and Why Do Mopar Lug Nuts Swell?

Ram 1500 trucks require 130 ft lbs (176 Nm) of torque to generate sufficient friction between the wheel pad and the brake rotor without over-stressing the M14 x 1.5 studs. Meanwhile, Mopar two-piece lug nuts swell when moisture penetrates the seam between the inner carbon steel nut and the outer stainless steel cap.

The Mechanics of M14 x 1.5 Clamping Force on Ram Hubs

In 2012, Ram switched from SAE 9/16 inch coarse studs to metric M14 x 1.5 fine-thread studs across the Ram 1500 lineup. Fine-pitch 1.5 mm threads create higher axial clamping force per pound-foot of wrench effort than older coarse threads. Consequently, dialing your torque wrench to the 2015 ram 1500 lug nut torque spec of 130 ft lbs (176 Nm) pulls the alloy wheel tightly against the 77.8 mm hub-centric bore. If you tighten those nuts to 160 ft lbs (217 Nm), the excessive clamping pressure distorts the thin steel brake rotor hat. That causes a noticeable steering wheel shake when braking from highway speeds.

Why Ram 2500 Trucks Split Between 130 Ft Lbs and 165 Ft Lbs

Heavy-duty 3/4-ton Ram 2500 pickups weigh over 6,500 pounds (2,950 kg) empty and tow heavy gooseneck trailers. Earlier Ram 2500 models equipped with single-piece conical acorn lug nuts used 130 ft lbs (176 Nm). That occasionally loosened under extreme commercial towing loads. So Ram updated the heavy-duty hardware to two-piece swivel flange lug nuts with a flat captive washer beneath the hex head. Because that flat flange washer reduces friction against the wheel face, Ram raised the torque spec to 165 ft lbs (224 Nm) on all Ram 2500 trucks using flange nuts.

The Root Cause of Swollen Dodge Ram Two-Piece Lug Nuts

Just like Ford, Stellantis and Mopar equip factory Ram 1500 wheels with two-piece capped lug nuts. Inside, a threaded carbon steel nut holds the wheel onto the stud. Outside, a thin decorative chrome or stainless steel cap is crimped over the steel core to resist rust.

When winter road salt, car wash detergents, or rainwater enter the tiny seam at the base of the cap, the inner steel core begins to oxidize. Rust expands up to six times the thickness of bare steel. That pushes the thin stainless shell outward from 22 mm to 22.5 mm or 23 mm. Repeated use of air impact guns by tire shops also twists the soft outer jacket. As a result, it becomes impossible to slide your factory 22 mm lug wrench onto the nut during a roadside flat.

Swollen two-piece Mopar lug nut next to a solid one-piece replacement for 2015 ram 1500 lug nut torque.

Step-by-Step Guide to Tightening and Removing Ram Lug Nuts by Severity

Your method for removing and tightening lug nuts on a Ram truck depends on whether you have clean hardware, swollen chrome caps, or rusted heavy-duty studs. Standard service follows a two-stage star tightening sequence on dry threads. Swollen or seized lug nuts require half-size extraction sockets and careful hub preparation before applying the 2015 ram 1500 lug nut torque.

Two Paths: Clean Hardware vs. Swollen or Seized Nuts

Follow the two numbered procedures below for standard maintenance and severe roadside extraction.

Process 1: How to Torque 2015 Ram 1500 Lug Nuts (Mild / Standard Case)

Use this two-pass star sequence whenever installing clean wheels on a 2012 to 2026 Ram 1500.

  • Scrub the Wheel Hub and Rotor Face: Brush away loose rust scale, brake dust, and mud from the flat brake rotor mounting pad and the 77.8 mm center hub ring using a wire brush. Wipe the M14 x 1.5 wheel studs completely dry with a clean cloth.
  • Hand-Thread All Lug Nuts Clockwise: Position the wheel onto the hub studs and thread every lug nut at least five full turns by hand. Starting the nuts with your fingers guarantees you do not cross-thread the fine M14 x 1.5 threads.
  • Snug the Nuts Lightly in a Star Sequence: While the tire still hangs 1 inch (2.5 cm) above the ground, snug the nuts to 30 ft lbs (40 Nm). This lets the conical seats center the rim on the hub.
  • Lower the Jack Until the Tire Supports the Truck: Lower the truck slowly until the rubber tire rests firmly on level concrete or asphalt. Keep the parking brake locked so the hub cannot spin.
  • Tighten Pass One to 65 Ft Lbs (88 Nm): Set your torque wrench to 65 ft lbs (88 Nm), which is half of the final 2015 ram 1500 lug nut torque rating. For 5-lug Ram 1500 wheels (2012 to 2018 & Classic), tighten in a 1-3-5-2-4 star pattern. For 6-lug Ram 1500 wheels (2019 to 2026 DT), tighten in a 1-4-2-5-3-6 crisscross pattern.
  • Tighten Final Pass Two to 130 Ft Lbs (176 Nm): Dial your calibrated torque wrench to 130 ft lbs (176 Nm) (or 165 ft lbs / 224 Nm for Ram 2500 flange nuts). Pull smoothly through the exact same star pattern until the wrench clicks once on every fastener.

5 lug and 6 lug star sequence for 2015 ram 1500 lug nut torque with two-pass tightening steps.

Process 2: Extracting Swollen or Seized Ram Lug Nuts (Moderate & Severe Cases)

If your 22 mm socket jams halfway onto a bulging Mopar lug nut, use these steps to remove it safely.

  • Switch to a 22.5 mm Half-Size Flip Socket (Moderate Swelling): Never pound a standard 22 mm socket onto a swollen nut with a hammer, as it will wedge permanently inside the socket. Slide a 22.5 mm six-point thin-wall extraction socket over the expanded chrome cap.
  • Loosen with a Long Manual Breaker Bar: Attach a 24 inch (60 cm) 1/2 inch drive breaker bar and pull counterclockwise with steady downward force. Avoid using an impact gun, which can shear the thin chrome cap free from the inner steel nut.
  • Remove a Spinning Chrome Cap (Severe Cap Separation): If the outer stainless shell spins freely around the inner nut, drive a sharp flathead chisel into the top center of the cap. Peel the torn metal jacket away with locking pliers to reveal the bare inner steel hex nut.
  • Unscrew the Exposed Inner Core with a 21 mm Socket: Once the outer cap is stripped off, the raw inner steel nut measures roughly 21 mm (13/16 inch). Seat a six-point 21 mm impact socket squarely onto the inner nut and turn counterclockwise with your breaker bar.
  • Clean Threads and Upgrade to Solid One-Piece Lugs: If rust binds the stud threads, apply two drops of penetrating lubricant to free the nut. Afterward, wash all oil off the stud with brake cleaner, dry thoroughly, and install solid one-piece forged steel lug nuts torqued to 130 ft lbs (176 Nm).

How Does Lug Nut Torque Change by Wheel Material and Ram Trim?

Wheel material and lug nut seat geometry determine which socket and fastener hardware your Ram truck requires. Factory aluminum alloy rims, steel work-truck wheels, aftermarket custom rims, and heavy-duty Ram 2500 wheels all require specific seat shapes. However, the clamping torque follows the stud and nut specification rather than rim color.

Factory Aluminum Alloy Wheels vs. Stamped Steel Spare Wheels

Most Ram 1500 Big Horn, Laramie, Rebel, and Limited trims feature cast aluminum alloy wheels with deep recessed lug pockets. Factory Mopar lug nuts use a wide 60-degree conical bulge seat that distributes the 130 ft lbs (176 Nm) load evenly across the aluminum taper. If you mount your underbody stamped steel spare wheel during a roadside flat, your factory 60-degree conical lug nuts will safely clamp the steel spare rim at 130 ft lbs (176 Nm). However, always verify that the decorative chrome cap does not bottom out against the thinner steel spare wheel before driving.

Aftermarket Custom Wheels and Spline-Drive Lug Nuts

  • Aftermarket Off-Road Wheels (Fuel, Method, Black Rhino): Custom aftermarket wheels for Ram trucks typically feature narrow lug wells that cannot accept a bulky 22 mm factory socket. These wheels require narrow-diameter 60-degree conical spline-drive lug nuts installed with a thin-wall spline key. Torque aftermarket M14 x 1.5 spline lug nuts to 130 ft lbs (176 Nm) on a Ram 1500 unless the wheel manufacturer stamps a specific lower limit on the rim.
  • Hub-Centric Bore Sizing (77.8 mm vs. 106.1 mm): Every 2012 to 2026 Ram 1500 hub has a center pilot lip measuring exactly 77.8 mm in diameter. Aftermarket wheels are often machined with a larger 106.1 mm or 108 mm center hole. Always install 77.8 mm to 106.1 mm hub-centric rings when mounting aftermarket wheels. That way the hub supports the truck weight instead of straining the studs.

Ram 1500 TRX and Ram 2500 Power Wagon Beadlock Wheels

  • Ram 1500 TRX (2021 to 2026): Despite its massive 702+ horsepower output and 35-inch tires, the Ram TRX uses the same six-lug M14 x 1.5 hub hardware torqued to 130 ft lbs (176 Nm). If your TRX has factory beadlock-capable wheels, the outer perimeter ring bolts require a separate low-torque sequence of 13 to 15 ft lbs (18 to 20 Nm) in a star pattern.
  • Ram 2500 & 3500 Heavy-Duty Models: Always inspect the base of your Ram 2500 lug nuts before setting your wrench. If the lug nut has a flat, free-spinning washer flange at its base, torque it to 165 ft lbs (224 Nm). If it is an older one-piece conical acorn nut without a flange washer, torque it to 130 ft lbs (176 Nm).

What NOT to Do When Torquing Ram 1500 and 2500 Lug Nuts

Never use an uncalibrated air or cordless impact wrench for final lug nut tightening on a Ram truck. Avoid applying grease, motor oil, or anti-seize to the wheel stud threads. And never torque a Ram 1500 to heavy-duty Ram 2500 specs. These mistakes snap studs and ruin brake rotors.

1. Never Tighten Ram Lug Nuts to Final Torque with an Impact Gun

A standard 1/2 inch mid-torque or high-torque impact wrench delivers 300 to 650 ft lbs (405 to 880 Nm) in seconds. Hammering a Mopar lug nut with an impact gun stretches the M14 x 1.5 wheel stud permanently and warps the brake rotor. Furthermore, rapid impact hammering splits and swells the thin stainless steel cap on factory Ram lug nuts. Use an impact wrench only on its lowest setting to spin loose nuts off. Always finish tightening by hand with a calibrated torque wrench.

2. Do Not Apply Anti-Seize or Oil to Wheel Stud Threads

Mopar engineering calculates the 2015 ram 1500 lug nut torque of 130 ft lbs (176 Nm) specifically for clean, dry metal threads. Lubricating the threads with anti-seize, oil, or penetrating spray eliminates thread friction. When you pull a torque wrench to 130 ft lbs on lubricated studs, the actual clamping tension spikes above 180 ft lbs (244 Nm). That stretches or snaps the steel stud. Keep the threads completely dry, and apply anti-seize only to the flat center hub bore ring.

3. Never Torque a Ram 1500 to Ram 2500 Flange Specs (165 Ft Lbs)

Because Ram 1500 and Ram 2500 trucks share the same M14 x 1.5 thread pitch, some owners mistakenly apply the heavy-duty 165 ft lbs (224 Nm) rating to a half-ton Ram 1500. Over-torquing a Ram 1500 aluminum wheel by 35 ft lbs crushes the softer aluminum lug seat. It can also crack the wheel around the bolt holes. Stick strictly to 130 ft lbs (176 Nm) on all Ram 1500 pickups.

4. Never Use a 12-Point Socket on Mopar Two-Piece Lug Nuts

A 12-point socket contacts only the fragile outer corners of a hex nut. Under 130 to 165 ft lbs (176 to 224 Nm) of force, a 12-point socket slips and rounds off the soft chrome cap instantly. Always use a six-point flank-drive impact socket that grips the wide flat faces of the lug nut.

5. Do Not Leave Your Torque Wrench Wound Up in Storage

Storing a click-type micrometer torque wrench set at 130 or 165 ft lbs keeps the internal spring under heavy compression. Over several months, spring fatigue shifts the wrench calibration by 15 percent or more. Always dial your torque wrench back to its lowest setting (such as 20 ft lbs) as soon as you finish tightening your wheels.

Long-Term Prevention Guide for Ram Wheel Hubs and Lug Nuts

Keeping your Ram 1500 or 2500 wheel hardware reliable requires a simple post-install, seasonal, and annual maintenance routine. Re-checking torque after driving 50 miles (80 km), upgrading to solid one-piece lug nuts, and maintaining proper tire inflation prevent roadside breakdowns. Follow this schedule to keep your wheels trouble-free.

Post-Install Re-Torque Check (After 50 to 100 Miles / 80 to 160 km)

  • Anytime you rotate your tires, mount a spare wheel, or install new rims, re-verify your 2015 ram 1500 lug nut torque after driving 50 to 100 miles (80 to 160 km).
  • Aluminum alloy wheels expand and settle slightly during initial highway braking heat cycles.
  • Set your torque wrench to 130 ft lbs (176 Nm) and check all lugs in a star pattern without loosening them first.

Every Tire Rotation (Every 5,000 to 7,500 Miles / 8,000 to 12,000 km)

  • Test-fit a clean 22 mm six-point socket over every lug nut by hand during each tire rotation.
  • If any factory two-piece lug nut feels tight or requires tapping to fit the 22 mm socket, replace the entire set with solid one-piece cold-forged steel lug nuts.
  • Clean the flat brake rotor face and the 77.8 mm center hub bore with a wire brush. Then apply a paper-thin film of anti-seize only to the center hub lip so the wheel never rusts onto the hub.
  • If your dashboard tire pressure light turns on after rotating wheels, reset the sensor locations.

Annual Emergency Roadside Kit Inspection

  • Inspect the factory scissor jack or bottle jack and lug wrench stored beneath the Ram front passenger seat or rear floor compartment once a year.
  • Add a 24 inch (60 cm) 1/2 inch breaker bar, a 22 mm socket, and a 22.5 mm half-size extraction socket to your auto emergency tool kit.
  • Having a long breaker bar in your truck makes breaking 130 to 165 ft lbs (176 to 224 Nm) of lug torque effortless during a roadside flat.

Clean wheel studs and 77.8 mm hub for 2015 ram 1500 lug nut torque with dry M14 x 1.5 threads.

Before you start

Tick these off as you gather them — nothing here is specialised.

0 of 8 ready · Ticks are for this visit only and aren't saved.

Common questions

What is the lug nut torque on a 2015 Ram 1500?

The official 2015 ram 1500 lug nut torque specification is 130 ft lbs (176 Nm). This torque setting applies to all 2015 Ram 1500 cab sizes, engine options, and factory steel or aluminum alloy wheels. Always tighten the five M14 x 1.5 lug nuts in a crisscross star pattern on clean, dry threads.

What is the lug nut torque on a 2016, 2017, and 2018 Ram 2500?

For a 2016, 2017, or 2018 Ram 2500 single rear wheel pickup, the lug nut torque is 130 ft lbs (176 Nm) if equipped with one-piece conical nuts, or 165 ft lbs (224 Nm) if equipped with two-piece swivel flange lug nuts. Always inspect the base of the nut for a flat washer flange before setting your wrench.

What is the lug nut torque for a 2020 Ram 1500 6 lug wheel?

The 2020 ram 1500 lug nut torque specification for fifth-generation 6-lug wheels is 130 ft lbs (176 Nm). Even though Ram upgraded the fifth-generation DT body truck from five lugs to a 6 x 139.7 mm bolt pattern, the M14 x 1.5 stud diameter and 130 ft lbs clamping specification remained unchanged.

What size socket fits a 2015 Ram 1500 lug nut?

A standard factory lug nut on a 2015 Ram 1500 requires a 22 mm (7/8 inch) deep six-point socket. If moisture and corrosion beneath the two-piece chrome cap have caused the nut to swell, you will need a 22.5 mm half-size extraction socket or a 23 mm socket to remove it cleanly.

Why did Ram 2500 lug nut torque change from 130 to 165 ft lbs?

Ram increased the Ram 2500 single rear wheel torque from 130 ft lbs (176 Nm) to 165 ft lbs (224 Nm) after introducing two-piece flat-washer flange lug nuts. The free-spinning flat washer reduces surface friction against the wheel pad, allowing higher torque to generate stronger clamping force for heavy commercial towing.

How do you remove swollen lug nuts on a Dodge Ram 1500?

To remove swollen two-piece lug nuts on a Ram 1500, use a 22.5 mm half-size extraction socket attached to a 24 inch (60 cm) manual breaker bar. If the outer chrome cap spins freely over the inner nut, peel the thin cap off with a chisel and pliers, then unscrew the inner steel core with a 21 mm socket.

What is the correct star tightening sequence for a 5 lug Ram 1500?

On a 5-lug Ram 1500 wheel (2012 to 2018 and Classic models), tighten the lug nuts in a 1-3-5-2-4 star pattern. Start at the top nut (1), cross down to the bottom-right nut (3), move across to bottom-left (5), go up to top-right (2), and finish at top-left (4) so the rim seats evenly.

Does a Ram 1500 Rebel or TRX have a different lug nut torque spec?

No, both the Ram 1500 Rebel and the supercharged Ram 1500 TRX use the exact same 130 ft lbs (176 Nm) main lug nut torque specification as standard Ram 1500 trucks. If your TRX has factory beadlock-capable wheels, only the smaller outer perimeter beadlock ring bolts require a lower 13 to 15 ft lbs (18 to 20 Nm) rating.

Should you put anti-seize on Ram 1500 wheel studs?

No, you should never apply anti-seize, motor oil, or grease to Ram 1500 wheel stud threads. Mopar's 130 ft lbs (176 Nm) torque specification is calibrated for clean, dry threads. Lubricating the threads reduces friction and causes you to over-stretch or snap the steel stud when pulling the wrench to 130 ft lbs.

How many miles after changing a Ram tire should you re-torque the lug nuts?

You should re-torque your Ram 1500 or 2500 lug nuts after driving 50 to 100 miles (80 to 160 km) following any wheel installation or tire rotation. Initial heat cycles and road vibrations allow alloy wheels to settle tightly against the hub face, making a quick torque check essential for safety.

Was this article useful?

Last updated .